Jump to content


Photo

Cooper T51 tech spec


  • Please log in to reply
9 replies to this topic

#1 Rainer Nyberg

Rainer Nyberg
  • Member

  • 1,768 posts
  • Joined: October 00

Posted 10 November 2000 - 13:13

Cooper T51

Technical Specification (1959)

Chassis :Type : Steel tube spaceframe
Designer : Owen Maddocks

Engine : Coventry Climax FPF
Type : 4-cylinder in-line, DOHC
Bore x Stroke : 94.0 x 88.8 mm (3.7 x 3.5")
Capacity : 2462 cc (151 cu in)
Compression : 12 : 1
Max power : 236 bhp @ 6750 rpm
Max torque : 204 lbft @ 5000 rpm
Carburettors : Two twin-choke Weber 58DCO3
Fuel pump : Ceco eccentric vane
Fuel tank : 150 litres (33 imp gallons)
Oil tank : 13.6 litres (3 imp gallons)
Oil filter : Tecalemit full flow
Cooling : Pump circulation

Transmission :
Gearbox : 4-speed Citroën-ERSA/Cooper
(5-speed Colotti unit used by Rob Walker´s team)
Ratios :
1st 9.06 (with 4.01 final drive)
2nd 6.39
3rd 5.03
4th 4.01
Clutch : 7.5" dry 3-plate Borg & Beck
Final drive : 2.96/3.21/3.45/3.72/4.01/4.32/4.66
with ZF limited-slip differential

Dimensions :
Wheelbase : 2310 mm (7' 7")
Front Track : 1180 mm (3' 10.5")
Rear Track : 1220 mm (4')
Overall lenght : 3520 mm (11' 6.5")
Overall width : 1380 mm (4' 6.25")
Overall height : 850 mm (2' 9.5")
Ground clearance : 114 mm (4.5")
Weight : 457 kg (1008 lb, 9cwt)
Weight distribution : 44/56

Brakes :
Front : 10.25" Girling discs
Rear : 9.75" Girling discs

Suspension :
Front : Wishbones and coil springs,anti-roll bar
Rear : Wishbones and transverse leaf-spring
Dampers : Armstrong adjustable telescopic

Steering : Cooper rack-and-pinion
Steering wheel : Sprung three-spoke, 15" diameter

Wheels :
Front and rear : Cooper cast-magnesium alloy, bolt-on

Tyres :
Front : 5.00 x 15"
Rear : 6.50 x 15"


Anyone out there that would like to make some additions/corrections ?

Rainer

Advertisement

#2 desmo

desmo
  • Tech Forum Host

  • 35,244 posts
  • Joined: January 00

Posted 10 November 2000 - 19:41

http://www.ddavid.co...ula1/cooper.htm

Not too in-depth, but this is an article by Dennis David on the Cooper era.

#3 oldtimer

oldtimer
  • Member

  • 1,291 posts
  • Joined: October 00

Posted 11 November 2000 - 02:26

Some would say 'spaceframe' was a rather loose use of the term on account of the curved tubes.

#4 Ray Bell

Ray Bell
  • Member

  • 85,550 posts
  • Joined: December 99

Posted 23 November 2000 - 11:29

Some salient points would be:
Rubber bushes or rose (Heim) joints in the suspension?
Adjustable dampers? Front spring height adjustable?
Were the wheels detachable?
These are little items that were in a state of flux at that time.

#5 oldtimer

oldtimer
  • Member

  • 1,291 posts
  • Joined: October 00

Posted 23 November 2000 - 19:09

Ray, I'm not a great one on specs., but I am sure the T51 did not have quick-detachable wheels. Those were for the front-engined monsters.

#6 Ray Bell

Ray Bell
  • Member

  • 85,550 posts
  • Joined: December 99

Posted 24 November 2000 - 03:07

Come to think of it, I'm sure I've seen photos with the wheels detached... alongside fences, ditches....

#7 oldtimer

oldtimer
  • Member

  • 1,291 posts
  • Joined: October 00

Posted 24 November 2000 - 03:26

What the hey, they spent most of their time on 3 wheels anyway.

#8 Ray Bell

Ray Bell
  • Member

  • 85,550 posts
  • Joined: December 99

Posted 24 November 2000 - 03:43

Too true...

#9 karlcars

karlcars
  • Member

  • 670 posts
  • Joined: February 00

Posted 25 November 2000 - 09:56

More detail on the Coventry-Climax engine will be available in the spring with the publication of my next book (after Ascari), called 'Classic Racing Engines'. It covers 50 engines over the years from the 1913 3-liter Peugeot to the 1994 Indy-winning Mercedes. I've tried hard to include complete specs for all the engines, including the Climax.

#10 Ray Bell

Ray Bell
  • Member

  • 85,550 posts
  • Joined: December 99

Posted 28 November 2000 - 20:12

Are you going to include the bit about the patterns for the engines being sold to Repco, Karl. And being thrown out when they cleaned up after the Repco disintegration?
FPFs were made in small numbers to keep the Australian National Formula One (2.5 litres) and Tasman Formula going. They had a special short stroke version, I think based on the bore of the 2.7 (which was 2751cc, was it not?), revved harder etc. Only a very small number built.
This was the lead in to the Repco V8s.