Jump to content


Photo

Repco modified Climax 2.5 FPF


  • Please log in to reply
8 replies to this topic

#1 Porsche718

Porsche718
  • Member

  • 913 posts
  • Joined: August 16

Posted 22 July 2020 - 11:13

Hey guys,

 

I'm after the modifications Repco made to the 2.5 Climax FPF engine for ANF1.

 

I get the impression that the bore/stroke ratio was altered which changed capacity slightly (from 2497 to 2495) but with an increase in power. Probably due to increased rev limit.

 

Anyone have the details, and the modified power output?

 

Cheers in advance, Steve



Advertisement

#2 Ray Bell

Ray Bell
  • Member

  • 85,550 posts
  • Joined: December 99

Posted 22 July 2020 - 14:06

They also tried a twin-plug setup...

 

The Climax heads always had provision for the drilling in of another spark plug hole. Repco tried it and got no power improvement and gave it away.

 

Geoff Smedley, however, working alone preparing John Youl's Cooper, fitted a second magneto. He has posted about that here, but there's a more comprehensive story in his book:

 

Approximately three months prior to this Tasman Series, John and I had spent considerable time discussing ways and possibilities of extracting more horsepower from the 2.5-litre Climax engine, to be more competitive with the later-type motors we knew would be used in the forthcoming series. At that time Repco were experimenting with dual ignition, which we had had in mind for months, and felt that there was horsepower to be gained.

 

We had several ideas but I wasn’t very keen to use coil ignition as Repco were doing. This would mean carrying a battery, coil, and all the things that could cause problems. So it was decided that two magnetos would be the answer if it was feasible to fit an additional one. Eventually I decided that by machining up an alloy block and welding it into the sump, it would be possible to squeeze in another magneto and clear the necessary chassis frames.
 

This called for some fairly accurate machining, as the new drive shaft would pick up at the bottom of the original helical drive gear which operated the existing magneto. In this way it would be sure that either magneto couldn’t get out of phase, and with fixed ignition in this way – I mean no automatic advance – using a 2º dwell in timing, it would give us better combustion using two spark plugs per cylinder.

 

All the parts were made up and the extra plug-holes added to the cylinder head, and the system was fitted up with two separate cut-out switches. This whole project took me about three weeks to complete, and then came the testing. We took the car up to the Symmons Plains circuit and spent quite a few hours testing and checking, trying different settings but reverting back to the first tunings we had originally made. The car’s performance seemed much improved, but by how much we really couldn’t tell.

 

So it was decided to take the car to Melbourne and run the engine on the dynamometer at the Repco research workshop. On arrival there was much shaking of heads, and while fitting the engine to the dyno we were virtually told we had just been wasting our time. Mr Frank Hallam, the chief of the research division, gave us all the information they had gained in similar experiments, the difference being that they were using two distributors driven from the rear end of the camshafts.

 

As they were using automatic advance on the ignition they found it impossible to hold synchronisation through the rev range, and found that the slight windup in the camshaft gave them unstable timing at the top end of the range. We had already thought of this problem, and felt that our fixed timing would work.
 

Within the next 30 minutes, after the motor had been warmed up, much interest was being shown as the power runs were tried and figures shown at various revs. All in all we spent some four hours testing and trying different timing settings, but finally settled on the original figures we had worked out in our own workshop. The horsepower was up by eight, with an additional eleven foot pounds of torque, the highest power reading ever given on Repco’s dyno for a 2.5-litre Climax engine, and we were delighted.

 

These figures may not sound anything wonderful, but when you are out on the track they make the difference between being competitive and not being competitive, and although the other drivers knew we were using this set-up they could only gauge the benefit of such an experiment by trying to catch the car in a straight line.

 

You might find a little interest in the graph, also printed in Geoff's book:

 

0720fr-GSbookclimaxgraph.jpg

 

I'm not at all sure what the 'Mk 1' and 'Mk 2' designations mean, but the bore and stroke shown there seems to be for the short stroke version and so it must have been two versions of that bore and stroke. Youl's engine, of course, was a long stroke.



#3 Roger Clark

Roger Clark
  • Member

  • 7,644 posts
  • Joined: February 00

Posted 22 July 2020 - 15:10

Mark 1 and Mark 2 refer to the two versions of the FPF produced by Climax in 1959. The Mk 1 had deliberately restricted output until they were sure of the reliability of the crankcase and connecting rods. The Mk 2 engines had larger valves and higher compression ratio.   I don’t think there was any short stroke engine at this time. 
 

The diagram, without the Youl curve was produced by Coventry Climax. It appears in a paper given by Wally Hassan to the SAE National Powerplant Meeting in 1960 and in Des Hammill’s book, Climax Racing engines. 



#4 Lee Nicolle

Lee Nicolle
  • Member

  • 11,330 posts
  • Joined: July 08

Posted 22 July 2020 - 22:56

A lot of work. For the last several decades the various ignition boxes, MSD Crane Mallory use would perform as well, if not better and use a LOT less power to drive.

These days to run a classic car on unleaded you need them to make the engine driveable, especially when cold.



#5 Ray Bell

Ray Bell
  • Member

  • 85,550 posts
  • Joined: December 99

Posted 23 July 2020 - 03:11

That would mean, Roger, that we don't know the answer to what Repco got out of their short stroke engines...

 

Or are those bores and strokes the short stroke figures?



#6 Porsche718

Porsche718
  • Member

  • 913 posts
  • Joined: August 16

Posted 23 July 2020 - 07:02

Ray, the bores and stroke specs on the Geoff Smedley power graph are as designed by Coventry-Climax. The 2497 cc capacity as far as far as I can recall is the Repco modified size.

 

I'm checking through the Sergent New Zealand website. I think it is talked about there I'm sure.

 

3.7 bore x 3.54 stroke = 2495.2 cc

 

Steve



#7 MarkBisset

MarkBisset
  • Member

  • 1,097 posts
  • Joined: September 15

Posted 23 July 2020 - 12:52

In the Nye/Brabham book Jack quotes 230bhp and 235bhp for the standard and short-stroke Repco prepped 2.5 FPF’s he used in the ‘65 Tasman

 

I can’t find the dimensions amongst my Repco clobber, Michael Gasking, who built the motors, remembers the short-stroke variant but he doesn’t have the details either. He thought Bruce McLaren may have been the initiator of the idea, I’m not so sure about that?

 

Jack left two of his 2.7 FPF’s with Frank Hallam and Michael at Repco’s Engine Lab in Doonside St, Richmond at the end of the 1963 NZ/Oz Intermationals- they were rebuilt over the next year as 2.5s to comply with the Tasman 2.5 Formula which commenced in 1964

 

Still lookin’, Stephen Dalton where are you...


Edited by MarkBisset, 24 July 2020 - 00:59.


#8 Ray Bell

Ray Bell
  • Member

  • 85,550 posts
  • Joined: December 99

Posted 23 July 2020 - 20:29

The short stroke versions were, presumably, 2.7s (no longer eligible for openwheeler racing in Australia or New Zealand) with new cranks...

 

So the bore would have been as for 2.7 engines.

 

I don't think there would have been much difference in the timing for Bruce and Jack to think about it, though Bruce would have had a crank made in England whereas Jack could have it done in relative secrecy at Repco.



#9 D-Type

D-Type
  • Member

  • 9,860 posts
  • Joined: February 03

Posted 23 July 2020 - 22:31

I've dug out some FPF bore & stroke figures on an old spreadsheet gleaned from various sources.

 

It gave  94 x 89.9  =  2495cc  for the 1960 engine  which matches  3.7 x 3.54 in   =   93.98 * 89.02 mm   =  2495 cc

and  96 x 95  mm  =  2750cc  for the Indianapolis engine

 

So if the Indianapolis bore was used with a shorter stroke it would have to be 96 x 86.2  =  2495cc