Jump to content


Photo
- - - - -

Downforce generation via increasing pressure


  • Please log in to reply
6 replies to this topic

#1 Ali_G

Ali_G
  • Member

  • 38,523 posts
  • Joined: August 00

Posted 02 June 2025 - 09:55

A quick question for the forum. Every method of downforce generation (and indeed lift with planes) I know of is by reducing pressure in the direction that downforce is being generated.

Are there any methods to create higher air pressure on upper surfaces of race cars in order to create additional downforce? Is this even being attempted in current rules set?

I’d imagine you could create higher pressure by deflection. However, I’d imagine aerodynamicists want airflow to attach to the bodywork as much as possible?

Edited by Ali_G, 02 June 2025 - 09:58.


Advertisement

#2 Bloggsworth

Bloggsworth
  • Member

  • 9,580 posts
  • Joined: April 07

Posted 02 June 2025 - 16:22

If you change the direction of airflow you create a pressure differential, so your deflector would create lift of its own, thereby defeating the purpose of the deflector...



#3 GreenMachine

GreenMachine
  • Member

  • 3,109 posts
  • Joined: March 04

Posted 02 June 2025 - 22:06

You are only looking at one part of a complex machine.

 

It is not just about lift (downforce).  It's about maximising the L/D ratio, IOW aerodynamic efficiency.  It is why these cars are not 'wing' cars, they are 'venturi' cars.

 

I am no aerodynamicist, but I am not understanding what you mean by a deflector.  If you are tying to increase the air pressure on the upper surface of the car, you are going down the path of flaps on an aeroplane wing.  These increase the lift, at a massive cost in drag, ie the L/D ratio drops, the aircraft can then still fly, but only slowly - which is the whole point: reducing landing/takeoff speeds.  We want fast cars everywhere, but especially on the straights.

 

The new regs allowing moveable aero may open up some opportunities along the lines you are thinking, but that is next year.  Aero efficiency will still be the objective, but maybe there are situations where what you want is effectiveness, and sacrifice efficiency for that.



#4 Ali_G

Ali_G
  • Member

  • 38,523 posts
  • Joined: August 00

Posted 03 June 2025 - 17:16

When I say deflection, I’m simply thinking that air can be deflected in an upward direction. Although that isn’t creating high pressure above the car. This may create downforce at enormous cost via Newton’s third law.

To counter that, I guess doing this would like create areas of low pressure above the car which would negate the effect.


Is there any way to decelerate the car over the car in order to create areas of high pressure?

#5 MattPete

MattPete
  • Member

  • 3,469 posts
  • Joined: January 00

Posted 26 September 2026 - 02:31

Maybe I’m misunderstanding, but isn’t that what the nose of the Intrepid GTP accomplished?

#6 10kDA

10kDA
  • Member

  • 1,895 posts
  • Joined: July 09

Posted 26 September 2026 - 12:36



Is there any way to decelerate the car over the car in order to create areas of high pressure?

That's what the familiar ducktail spoilers developed in the 60s did. They slowed the flow off the tail of the car, increasing the pressure which acted at the base of the spoiler. Also - see the transverse strip across the noses of the Lotus 49B & -C and 72 for similar flow-slowing pressure-increasing deflectors. The fences along the edges of the Matra MS80 nose kept the air from spilling over the sides, increasing volume of air, not flow nor pressure though both are affected, acting on the upper surface of the nose, creating downforce via impact "pressure", plus diminishing the effect of flow off the top of the nose interfering with air deflected by the front wings. Deflecting air flow does work to increase pressure but the downside (see what I did there?) is it is less effective when you can't take advantage of a low pressure area which develops on the opposite face, as what happens when using a more-or-less airfoil-ish shape. In the absence of an effective lower surface, see the McLaren M8F (full-length fences channeling upper surface air to a large rear wing), Lotus 56 and to a lesser extent, the basic shape of the 72. Practice vs theory. The principles put to use on these cars were proven to work.



#7 kumo7

kumo7
  • Member

  • 12,758 posts
  • Joined: May 15

Posted 07 October 2026 - 08:24

when an object travel very close to the ground suface, it has to push air in front of the object. This creates resistances which increases to its frontal projection surface area.
you can design a car that pushes this air volume as much as possible towards up wards, through which you could control the pressure on the upper surface that it achieves higher air pressure.
The pushed aside air, after reaching the highest point, now being pressured by the above, or the atmosphere, creating down wash. by controlling the flow. it could increase the pressure above the upper surface of the object.
I believe that Red Bull F1 around 2010 used this down wash principle. the water sliders of 2025 cars, i think, accelerates this downwash by setting the vortex into a smooth trench.
Someone has to sort out the complex shapes of the car tho. and i have not done this never ever!